Kennel Gear Brand, .5" Surface Mount with Adhesive Backing

½" Adhesive Dog Kennel Surface Mount — Piranha Lox® Locking System with 3M™ Adhesive Backing for Smooth Non-Porous Surfaces

The Kennel Gear ½" Surface Mount with Adhesive Backing brings the full Piranha Lox® locking system to surfaces where screw installation isn’t practical or permitted. Backed with 3M™ High Strength Acrylic Adhesive 300LSE, this dog kennel adhesive surface mount bonds directly to glass, stainless steel, aluminum, and other hard smooth non-porous surfaces — giving kennels, veterinary wards, grooming facilities, and home dog feeding areas a tool-free mounting point for any compatible Kennel Gear bowl, pail, or accessory without drilling into the surface.

Key Features

• Piranha Lox® adhesive dog kennel surface mount — accepts the insert block built into all compatible Kennel Gear bowls, pails, and other accessories; spring-loaded release tab disengages any insert block in one motion without tools
• 3M™ High Strength Acrylic Adhesive 300LSE backing — bonds to glass, stainless steel, aluminum, and other hard smooth non-porous surfaces without screws or drilling
• Two center screw holes — for installations where supplemental mechanical fastening alongside the adhesive is preferred or required
• Anodized aluminum construction — corrosion resistant and low profile for daily use across commercial kennel and residential environments
• Compatible with all Kennel Gear universal insert mounts — bowls with yokes, pails with insert blocks, IV poles, supply caddies, and any accessory with a compatible insert block

The 3M™ 300LSE adhesive is engineered for the low surface energy materials common in kennel and veterinary environments — stainless steel panels, glass partition walls, and powder-coated aluminum surfaces that standard adhesives fail to grip reliably. For facilities where surfaces cannot be drilled or where a permanent screw mount would damage the installation surface, this no-drill kennel mount delivers the same Piranha Lox® locking performance as the standard screw-mount version. Compatible accessories include the 1 Pint Stainless Steel Bowl with Aluminum Yoke and the full range of Kennel Gear stainless steel bowl and pail systems.

For best adhesion results on this adhesive dog kennel surface mount, ensure bonding surfaces are clean and dry before application. Apply firm pressure for approximately 20 seconds and use moderate heat between 100°F and 130°F to activate full bond strength. Allow a minimum of one hour for the adhesive to establish full contact before loading. Best applied at ambient temperatures between 70°F and 100°F. Where adhesive bonding alone may not be sufficient, the two center screw holes allow supplemental mechanical fastening. For a screw-mount alternative, see the ½" Surface Mount. For full compatibility details across the Kennel Gear accessory range, refer to the Kennel Gear System Fit and Compatibility Guide.

What’s Included

• ½" anodized aluminum adhesive dog kennel surface mount with 3M™ High Strength Acrylic Adhesive 300LSE backing and spring-loaded release tab

Dimensions

• 3.125" L x 2.00" H x 0.50" D

Disclaimer

Product Use

All statements, technical information and data contained in this document are based upon tests or experience that 3M and Kennel Gear USA LLC believe are reliable. However, many factors beyond 3M’s and Kennel Gear USA LLC’s control can affect the use and performance of a 3M product in a particular application, including the conditions under which the product is used and the time and environmental conditions in which the product is expected to perform. Since these factors are uniquely within the user’s knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for the user’s method of application.

Warranty, Limited Remedy, and Disclaimer

Many factors beyond 3M’s and Kennel Gear USA LLC’s control and uniquely within the user’s knowledge and control can affect the use and performance of a 3M product in a particular application. User is solely responsible for evaluating the 3M product and determining whether it is fit for a particular purpose and suitable for the user’s method of application. Unless an additional warranty is specifically stated on the applicable 3M product packaging or product literature, 3M and Kennel Gear USA LLC warrant that each 3M product meets the applicable 3M product specification at the time 3M or Kennel Gear USA LLC ships the product. 3M AND KENNEL GEAR USA LLC MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE.

Limitation of Liability

Except where prohibited by law, 3M and Kennel Gear USA LLC will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability.